mgf.be

[andrew]

Well the FPR arrived but with out the requested gauge for adjustment. Never mind the workshop has one, so they start work on Tuesday............... its getting closer.........
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[Bruce]

How would you typically calibrate that? I know Bruno did his during a rolling road test end just kept adjusting until he got the best performance result. Will you do the same? Or is there an alternative?
_________________
Witte pinkers,stoelverwarming,K&N 57i,52 mm TTB,glazen windscherm,Chrome boutjes- asbak- aansteker,LLW kitje,mk2 middensteun,de-cat pijp,Phoenix exhaust,TF-LE-80th An. velgen,TF radiator,LR pakking,Trophy splitter,lowering pins,HID koplampen,Momo pook,zwarte raamomlijsting,Alu. teller ringen,zwarte trophy inserts,trophy uitlaat spruitstuk,mk2 downpipe,AP's,304 schijven,TF135 Cams,Trophy spoiler,Viper stripes,Magnacor leads

[andrew]

My guy say's using an exhaust gas analizer, will be 98% correct!. He does have plenty of experiance not just of F's, but old and BMW Minis plus his own very hot WRX.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[andrew]

Well the workshop got busy and as my car was not on the urgent list, it was left until the last moment and nothing had been done. The only trouble was that I decided to do a motorkhana on the saturday so I retrived my car but with one difference. I had complained of a rattle from my exhaust, it was descoverd that my catalist had disintergrated so a pipe was welded through it making it a de-catted F, this coupled with a Miltek SS exhaust. I now have the loudest F in Australia which is causing a problem or two as it's even more than the 95 decibel limit for race tracks. As our National Meet is only just over a week away, I have left all modifications till the first week of May except if I can find one , a new/secondhand cat'.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[Mr. Dj M.]

Quite irritating when people don't do what they said they would do, hopefully you will get help

[andrew]

Well have started to strip down the engine but before I fit the new head and cam does any one have pictures of the correct position of the offset dowels.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[ErikB]

I am sure Bruno and/or Sander will pop in to help you with the dowels. I haven't got them myself (set of veniers on the shelf), but they have them on their cars.

[andrew]

Well have just got the F back, had another minor set back, after fitting the FPR it would not pull, after pulling their hair out the workshop found the fuel pump had given up. I have a half roll cage, this componded the problem as it had to come out to get to the fuel pump. To get the cage out the seats have to come out. The O.E pump is expensive over here but we found a Bosch high presure one that was built for a Holden Commadore Turbo at the cost of only $100. I have only driven 15km so far,noticed more torque and a car that pulls all the way to the rev limiter. The real proof will be at the weekend when I go to a hill climb http://vimeo.com/1460777 .
Has it been worth it, I will let you know next week.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[Mr. Dj M.]

Sounds good already, hopefully it stays that way for you

[ErikB]

A bit of a strange thing that the fuel pump gives up, just after some work has been done on a FPR. Are you sure they didn't screw up.
If the fuel pump is suspected, you may never forget to have a look at the connector on top of the pump. Some of them desintegrate in a rather spectacular way.

[andrew]

My car a 98 MG F VVC has done 161000km so I was not surprised that it packed up when asked to do more, and at least I should not have a problem in that area for a while ( fingers crossed). Today I hav e just returned from a quick blast of 100km on all types of road to see what she can do, the exhaust is much deeper in sound and the power from 5000 to 7250, well it just PULLS and PULLS using an exhaust gas analiser the FPR is showing4.1bar on the dial. Tomorrow I am getting just a pwer dyno test done to get an idea whats at the rear wheels and then I hope the weather stays nice for the hillclimb at the weekend.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[andrew]

Power dyno result 90kw at 7100rpm, it feels stronger than that!
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia

[ErikB]

That will be 122bhp, at the wheels I suppose.
Resulting in a 141bhp at the flywheel.

Is there a chance you could post the graph, as top power doesn't say much ?

[Carl]

141 BHP at the flywheel, about as much as the VVC, but possibly much better spreading around the RPM range.
The non-vvc has much better torque, so the figure sounds interesting.

Eager to see the graph too!

Have a great time at the Hillclimb this weekend! (some pictures are always welcomed )
_________________
MGF 1999 1.8iVVC LHD pearlescent British Racing Green 75th anniversary multi-spoke wheels, 75th edition, no LE ! mods: witte pinkers,
MGF 1996 1.8iVVC RHD Metallic British Racing Green . VVC velgen, no mods.
todo: genoeg voor de volgende 1,5 jaar .
Als je iets doet, doe het dan goed!

[andrew]

Could not work out how to post dyno graph so sent it to Bruce.
_________________
MG F Captain - MGCC Victoria
MG F Register Regional Representative - Eastern Australia